MODULE 9 HUMAN FACTORS QUESTIONS

Multiple Choice Quiz

Module 9: Human Factors

1) Motor programmes are behaviour subroutines
2) "Risky Shift" is a tendency to take more risky decission in a group
3) During visual scanning the eye movement should be small and frequent
4) The amount of stress experienced with a particular task is dependent
on the perceived demand and perceived ability
5) An excessive noise level would increase performance never

1) The cycle REM sleep and stages 1-4 sleep
occurs about every 90 minutes
2) The alerting system for an important system failure should
be a flashing visual signal, preferably red
3) One of the main problems encountered when using a routine check list is
that individual responses may become automatic rather than diligent
4) Long shift work will decrease your maintenance ability
5) If a person is colour blind which colours would be most difficult to see red and green

1) phase 3 and 4 sleep is most beneficial for the bodies recovery
2) Human error is due to low body temperature
3) In a discussion the person who is most likely to be agreed with
is the person w ith highest status
4) after a long night shift what meal is most
recommended one in high carbohydrates (to increase sugar level)
5) Long shift work will decrease your diagnostic and maintenance ability

1) A good scan is best achieved by frequent and small eye movement
2) Stress is caused by the perceived ability is insufficient to cope with the perceived demand
3) A major source of error using checklists is they may be responded to automatically
4) Detail is best sensed by the........and movement best sensed by the
...... the fovea & the periphery
5) Stress management is coping with the stress

1) Skill based behaviour is associated with motor programme
2) Rule based behaviours are stored in the long term memory
3) an individual is likely to comply with a decision made by someone of greater status
4) to minimize the chances of heart disease, it is recommended that a minimum amount of exercise
should be 3 times a w eek with the heart rate doubling the normal rate for at least 20 minutes
5) Stress in an individual is largely dependent on evaluation of ability and the demands placed on it.

1) Conductive deafness can be caused by damage to the Cochlea
2) Information on drugs and alcohol can be found in AWN 47
3) 70-80 % of the total focusing ability of the eye is carried out by the corne
4) After general anaesthetic you
should you must not return to work for at least 24 to 48 hours (w hich w ill depend on the individual)
5) Your doctor has prescribed you tranquillisers as you are suffering from a fit what should you
do. should not work when taking them.

1) The pupil of the eye grows smaller In conditions of increased light
2) The area of the brain which interprets information from the eyes is known as:
the visual cortex
3) peripheral vision is obtained by the part of the eye known as the rods
4) Information in the short term memory must be actively rehearsed to ensure long term retention
5) Following consumption of alcohol is safe to fly or work on
aircraft at a time after the last drink dependent on the amount of alcohol

1) during visual scanning the eye movement should be small and frequent
2) the amount of stress experienced with a particular task is dependent on
the perceived demand and perceived ability
3) The cycle of REM sleep and stage 1-4 sleep
occurs about every 90 minutes
4) The alerting system for an important system failure should
be; a flashing visual signal, preferably red
5) One of the main problems encountered when using a routine check list is
that individual responses may become automatic rather than diligent

1) An excessive noise level would increase performance never
2) Long and short sightedness is caused by distortion of eye ball
3) The cycle of REM sleep and stage 1-4 sleep
occurs about every 90 minutes
4) The alerting system for an important system failure should
be a flashing visual signal, preferably red
5) After dental treatment involving anaesthetic a pilot should not fly for a period
of 24 hours

1) The part of retina which has the highest visual acuity is the fovea
2) The effect of smoking 20 cigarettes a day is to increase the apparent ambient pressure by 5 to 6 thousand feet
3) The composition of the atmosphere at sea level is 78% Nitrogen, 21 % oxygen, 1% other gases
remain constant up to about 70 000 feet
4) The capacity of the working memory may be expanded by chunking the information
5) The heart muscle requires its own blood supply. This is provided by the coronary arteries

1) Raised blood pressure (hypertension) is the main risk factor in the development of
strokes
2) A man is considered to be obese if his body mass index is over 30
3) The major factor in the general population which predisposes to heart attack
is family history
4) Loss of hearing due to damage in the eardrum or auditory is known
as conductive deafness
5) the physiological response to high level of stress
are sw eating, dryness of the mouth, breathing difficulties

1) The working memory is limited in its capacity to store unrelated items. The number of such items
which may be stored with full retention is 7 +/-2
2) If information in the working memory is not rehearsed it will be lost in 10 to 20 seconds
3) Anthropometry is the study of human measurements
4) In the event of rapid decompression, the venturi effect may lead
to The cabin altitude being at a greater altitude than the aircraft altitude
5) Sinuses in the skull are required To make the skull lighter and the voice resonant

1) Red blood cells are produced in the body by the bone marrow
2) The function of nasal passage are
to filter warm and humidify air drawn in during inspiration
3) A person who has been SCUBA diving should avoid
flying with 12 hours or 24 hours if a depth of 30 feet has been exceeded
4) The composition of the atmosphere from sea level to about 70 000 ft retains proportions
of 21% oxygen, 78% nitrogen, 1% other gases
5) Oxygen is required by the human body
to derive energy from food by chemical oxidation

1) Gas exchange between the air and blood takes place
Between the interior of the alveoli and the capillaries on the alveoli
2) Oxygen is transported in the blood in combination w ith haemoglobin in the red blood cell
3) An individual who is short of oxygen may try to compensate by increasing the rate and depth of
breathing. This process is called hyperventilation
4) strengthening and organizing the human memory when learning new tasks is believed to occur
in REM sleep
5) The area on the retina where the optic nerve receives all the information from the nerves of the
retina is the blind spot

1) The eye adjusts to changing light intensities by varying the diameter of the iris. This can reduce the
amount of light on the retina by a factor of; 5 : 1
2) The ideal behaviour of a professional aircraft engineer both person and goal directed
3) Decisions made by a group are
generally better in quality than the average decisions made by the individual group members
4) Which of the following personality would be the most likely to have an accident through
risks anxious extrovert
5) The lower threshold of noise that will cause permanent 90db

1) The part of the eye most responsible for focusing an image on the retina is
the cornea
2) Myopia is ..... and a ...... lens is needed to correct it short sightedness & concave
3) The factor which contributes most in assessing an individual’s risk of developing artiery disease
is family history
4) Amnesia tends to affect episodic memory
5) As we get older our response to generally tends to become slow er and more accurate

1) Absenteeism is an extreme form of the stress coping strategy known as action coping
2) During a typical nights sleep most time is spent in which stage of sleep 3 & 4
3) The sleep cycle of REM and stage 1-4 sleep repeats during the night approximately
every 90 minutes
4) The best visual scan pattern to enable maximum information to be obtained is
Achieved making as many movement as possible
5) The most common cause of focusing problems for people with uncorrected vision
is an elongated eye

1) The maximum duration for which visual and sensory memory can store information is
approximately 1 seconds
2) Risky shift is the name given to the occasion when
an individual member of the group is persuaded by the group to make a more risky decision than he w ould have made alone
3) The behaviour pattern used to carry out procedure such as an ultra NDT check is
a rule based procedure
4) Stress management programme involves none of the above
5) The extent of damage suffered by an ear following exposure to loud noise is dependent
upon the intensity and duration

1) The ability to hear your name mentioned while concentrating on another task is known as
the cocktail party effect
2) Physical and visual stimuli are stored in short term memory
3) A domestic problem will affect concentration and decision making abilities
4) The credit and debit system for measuring sleep/wake cycles
allocates 1 points for sleep 2 point awake
5) The circadian rhythm exhibits an uncontrolled 25 hours

1) a group is more likely to be riskier than that of an individual
2) The iconic memory, the visual store of short term memory, will hold information for
½ to 1 seconds
3) A unit of alcohol is equivalent to half pint of beer or a standard glass of wine or measure of spirit.
After two or three units of alcohol in an evening the affect on sleep will be loss of REM sleep
4) The part the eye which bends most light is the cornea
5) Of the following the risk factors which are associated with
coronary smoking

1) An attention mechanism is required in the human information processing sequence because
working memory and processing capacity is limited
2) A motor programme is learned behaviour not requiring conscious thought
3) Before making a non-urgent decision a good leader
should encourage suggestions before stating his own opinion
4) If during an engine ground run you experience a fire, and you carry out the required drill, you
exhibit rule based behaviour
5) slow wave sleep restores the body and occurs early in the sleep period

1) the carbon dioxide is transported in the human body by the blood
in slution as carbonic acid
2) a unit of alcohol is equivalent to a half pint of beer or a standard glass of wine or measure of spirit.
In excess or 21 units for a male or 14 units for a female will damage vital organs if consumed regularly
in a period of 1 week
3) The group decision is .... than are made by an individual and ... extreme which of the following fills
the blanks correctly better & more
4) The rate and depth of breathing is normally related to
the amount of carbon dioxide in the blood and lungs
5) Taking alcohol before sleep has an effect upon sleep
pattern reduces REM sleep and induces early waking

1) in the dimension of personality a changeable aggressive is an anxious extrovert
2) In the eye details is seen best by .......and movement...... which of the following corretly substitutes
the missing words the fovea & the periphery.
3) Which of the following events will cause an individual the most stress breavement of a partner
4) Our model of the world is based upon sensual perception and past experience
5) What is the most common cause of long or short sight shape of the eye ball

1) The body removes alcohol from the system at 1 to1.5 units per hour. What is the minimum time
that total abstinence should be observed by a Prudent pilot flying 24 hours
2) The long term memory can be classified as two types ‘semantic and episodic’
semantic’ is more accurate and longer lasting then ‘episodic’
3) The relative stimulation and responses of the brain to stimuli from the senses varies. Which of the
following is
true visual stimuli attract attention slower than auditory but result in a more accurate response
4) stress can have a positive effect on ability
5) stress management consist of isolating the stressor and evolving a coping strategy

1) A consumption of Alcohol above the following level can cause permanent damage in the body of
male 5 units daily/21 units a week
2) Skin contact with aviation fuels should be immediately treated by
copious washing of the skin with cold water only
3) At the fovea resolving power rapidly decreases a small number of degrees from its centre
4) Conductive deafness can be caused by damage to the ossicles
5) 70-80 % of the total focusing of the eye is carried out by the cornea

1) A good scan is best achieved by frequent and small eye movement
2) Stress is caused by the perceived ability is insufficient to cope with the perceived demand
3) A major source of error using checklists is they may be responded to automatically
4) Detail is best sensed by the ......... and movement best sensed by the
........ the fovea & the periphery
5) Echoic memory is the ......... sensory store and last for ..... whereas Iconic memory is the ......sensory
store and last for auditory & 2-8 seconds & visual & 0.5-1 second

1) The affliction, which causes the greatest number of deaths in the world each year is
Malaria
2) Symptoms directed coping of stress is achieved by taking cup of coffee
3) The most common cause of myopia is an elongated eyeball
4) what light sensitive cells are on the fovea? cones only
5) The automatic phase of a motor programme may revert ....... phase when stress is
introduced. associative

1) Skill based behaviour is associated with motor programme
2) Personality is resistant to change
3) The light sensitive cells on the optic nerve are none
4) The Otoliths detect linear acceleration
5) Counselling is a tool that can be used to cope with stress. It is a form of: symptom directed coping

1) The normal recovery for Circadian daysrhythmia is at a rate of 1.5 hours a day
2) Clinical insomnia can be caused by caffeine
3) In treating hyperventilation the patient should be made to breathe slowly and deeply
4) Rule based behaviours are stored in the long term memory
5) If REM sleep is insufficient it will be made up during the following night’s sleep

1) The most reliable sense for spatial orientation is vision
2) selective attention is another name for cocktail party effect
3) an individual is likely to comply with a decision made by someone of greater status
4) to minimize the chances of heart disease, it is recommended that a minimum amount of exercise
should be 3 times a w eek with the heart rate doubling the normal rate for at least 20 minutes
5) Having attained night adaptation, maximum visual acuity is achieved by
looking slightly to one side

1) For a person suffering from short-sightedness, close objects are seen ....... and distant objects are
seen........ in focus & out of focus
2) Linear acceleration is sensed by the otholiths
3) The normal response time is 200 milliseconds
4) Which of the following is
true episodic memory can be influenced by expectations as to what should have happened
5) Stress in an individual is largely dependent on evaluation of ability and the demands placed on it

1) Conductive deafness can be caused by damage to the Cochlea
2) Most of the time of a typical sleep is spent in stage 2 sleep
3) The shape of graph when stress is plotted against performance could be described
as a inverted curve
4) One unit of alcohol is approximately half pint of beer or one standard glass of wine or spirits
5) It is generally true that decision is reached by a group is ........... than the average decision made by
an individual within that group better

1) The nose filters, warms and moistens the air into the lungs
2) Alcohol is broken down by the body at an approximate rate of 1 unit per hour
3) The maximum number of sleep credits which can be obtained is 16
4) Accident and engineering faults are significant and increasing
5) Information on drugs and alcohol can be found in AWN 47

1) 70-80 % of the total focusing ability of the eye is carried out by the cornea
2) At what distance should a person without hearing difficulties be able to hear an average
conversational voice in a quiet room 2 metres (6feet)
3) If you have been prescribed new medication by your doctor you
should give the new medication a 24 hours trial
4) After general anesthetic you
should you must not return to w ork for at least 24 to 48 hours
5) Your doctor has prescribed you tranquillisers as you are suffering from a fit what should you
do should not work when taking them

1) The use of ‘pep’ pills by an aircraft engineer
should never be taken as coffee is the only stimulant permitted
2) You are taking ‘SUDAFED’ because you are require relief from nasal congestion
you must avoid making engineering decisions or performing licenced duties
3) A perforated ear drum could occur if you were subjected to continuous noise below 8 KHz
4) How long is short term memory valid for after memorizing seven items up to 30 seconds
5) What is peer group pressure
in certain situation are reactions are influenced by the group, this is sometimes against our better judgement

1) What is white finger
a disorder of the finger which may occur through continuous use of pneumatic tools because of reduced blood flow
2) What is slow wave sleep stage 3 and 4
3) What constitutes a good hand over written plus verbal
4) Consequences of environmental stress could result from noise, fumes, heat and vibration
5) The regular behaviour of an individual is habit

1) phase 3 and 4 sleep is most beneficial for the bodies recovery
2) Human error is due to low body temperature
3) In a discussion the person who is most likely to be agreed with
is the person w ith highest status
4) after a long night shift what meal is most
recommended one in high carbohydrates (to increase sugar level)
5) Long shift work will decrease your diagnostic and maintenance ability

1) How does a company best facilitate a shift hand over
every individual from the on coming shift must get a personal handover of the job they taking over
2) When someone is working in an enclosed space
they require extra supervision and better communication to increase the safety aspect
3) an engineer who has developed his own way of performing a difficult
task is in regular violation
4) The circadian cycle body temperature vary by 1.5 degrees F
5) If a person is colour blind which colours would be most difficult to see? red and green

1) When eye defect has been corrected by glasses or contact lenses, what is an acceptable value
an acceptable level of vision should be restored
2) Long shift work will decrease your maintenance ability
3) what is the recommended time for a pilot to wait after drinking alcohol before reporting for
duty 24 hours
4) The circadian cycle body temperature vary by 1.5 degrees F
5) If a person is colour blind which colours would be most difficult to see? red and green

MODULE 9 HUMAN FACTORS

HERE ARE THE LINKS REQUIRED FOR THIS MODULE
CAA UK/CAP715
CAA UK/CAP716
CAA UK/CAP562

Mod 9 Human Factors

9.1 General

The aviation industry is growing, and if we continue the same way we are working, currently we will have soon one fatal accident per week! In order to stop this, we must also consider the human being as a factor, as about 70% of the maintenance related accidents come
from improper installation etc... The need to take human factors into account
"Human factors" refers to the study of human capabilities and limitations in the workplace. Human factors researchers study system performance. That is, they study the interaction of maintenance personnel, the equipment they use, the written and verbal procedures and rules they follow, and the environmental conditions of any system. The aim of human factors is to optimize the relationship between maintenance personnel and systems with a view to improving safety, efficiency and well-being Human factors include such attributes as:

human physiology psychology (including perception, cognition, memory, social interaction, error, etc.) work place design environmental conditions human-machine interface anthropometrics (the scientific study of measurements of the human body) To understand human factors, the SHEL model can help. Software (e.g. maintenance procedures, maintenance manuals, checklist layout, etc.) Hardware (e.g. tools, test equipment, the physical structure of aircraft, design of flight decks, positioning and operating sense of controls and instruments, etc.) Environment (e.g. physical environment such as conditions in the hangar, conditions on the line, etc. and work environment
such as work patterns, management structures, public perception of the industry, etc.)
Livewire (i.e. the person or people at the centre of the model, including maintenance engineers, supervisors, planners, managers, etc.). Incidents attributable to human factors human error
Most problems that were leading to accidents are: There were staff shortages Time pressures existed All the errors occurred at night Shift or task handovers were involved
They all involved supervisors doing long hands-on tasks There was an element of a can-do attitude Interruptions occurred There was some failure to use approved data or company procedures Manuals were confusing There was inadequate pre-planning, equipment or spares.

Murphy's Law
There is a tendency among human beings towards complacency that an accident will never happen to me or to my Company. ("If anything can go wrong, it will") It was named after

9.2 Human Performance and Limitations
Just like aircraft components have limitations, engineers also do have certain capabilities and limitations.
Vision: Please study the Basic Function of the Eye! (CAP 715)
You should understand Pupil, iris, lens, cornea, retina, cones & rods, optic nerve to the visual cortex in the brain, and Myopia, presbyopia, hypoxia, Color Vision - see CAAIP!
When a person is tired accommodation is reduced, resulting in less sharp vision (sharpness of vision is known as visual acuity). Cones function in good light and are capable of detecting one
detail and are color sensitive. This means the human eye can distinguish about 1000 different shades of color. Rods cannot detect color. They are poor at distinguishing one
detail, but good at detecting movement in the edge of the visual held (peripheral vision). They are much more sensitive at lower light levels. As light decreases, the sensing task is passed from
the cones to the rods. This means in poor light levels we see only in black and white and shades of grey. Visual acuity is the ability of the eye to discriminate sharp detail at varying distances.
Various factors can affect the eye: Physical factors such as: physical imperfections in one or both
eyes (short sightedness, long sightedness),age The influence of ingested foreign substances such as: drugs, medication, alcohol, cigarettes. Environmental factors such as: amount of light available, clarity of the air (e.g. dust, mist, rain, etc.). Factors associated with object being viewed such as: size and contours of the object, contrast of the object with its surroundings, relative motion of the object, distance of the object from the viewer, the angle of the object from the viewer. Color-defective vision (normally referred to incorrectly as color blindness) affects about 8% of men but only 0.5% of women. The most common type is difficulty in distinguishing
between red and green. More rarely, it is possible to confuse blues and yellows. - see CAAIP!
Individual light requirements doubles with age. Glare of light affects older people more
For crack inspection hold light at an angle of 5 to 45 degrees to the surface to be checked
Perception is what you are expecting to see For more see exam questions!

Hearing: see CAP 715!
The Basic Function of the outer ear, middle ear and inner ear.
You should know auditory canal, eardrum, ossicles, acoustic or aural reex, Eustachian tube, cochlea, basilar membrane, auditory nerve. The amount of vibration detected in the cochlea depends on the volume and pitch of the original sound. The audible frequency range that a young person can hear is typically between 20 and 20,000 cycles per second (or Hertz), with greatest sensitivity at about 3000 Hz.
Normal hearing is from 20 Hz to 20,000 Hz
Hangar noise is about 70 to 75 decibel
Earplugs reduce noise by 20 decibel
Earmuffs reduce noise by 40 decibel
Impact of Noise on Performance It can: be annoying (e.g. sudden sounds, constant loud sound,
etc.); interfere with verbal communication between individuals in the workplace; cause accidents by masking warning signals or messages; be fatiguing and affect concentration, decision making, etc.; damage workers hearing (either temporarily or permanently). It is normally accepted that a TWA (Time Weighted Average sound level) noise level exceeding 85 dB for 8 hours is hazardous
and potentially damaging to the inner ear. Exposure to noise in excess of 115 decibels without ear protection, even for a short duration, is not recommended. Presbycusis is hearing deteriorates naturally as one grows older. Hearing test: The ability to hear an average conversational voice in a quiet room at a distance of 2 meters (6 feet) from the examiner is recommended as a routine test.

Information Processing
Information processing is the process of receiving information through the senses, analyzing it and making it meaningful. Sensory Receptors and Sensory Stores Physical stimuli are received via the sensory receptors (eyes, ears, etc.) and stored for a very brief period of time in sensory stores (sensory memory). Visual information is stored for up to half a second in iconic memory and sounds are stored for slightly longer (up to 2 seconds) in echoic memory. This enables us to remember a sentence as a sentence, rather than merely as an unconnected string of isolated words, or a _lm as a _lm, rather than as a series of disjointed images. Attention can be thought of as the concentration of mental effort on sensory or mental events. You should know Selective attention cocktail party effect , Divided attention , Focused attention , Sustained attention and
that attention is influenced by arousal level and stress. Perception can be defined as the process of assembling sensations into a useable mental representation of the world. Perception creates faces, melodies, works of art, illusions, etc. out of the raw material of sensation. Decision making is the generation of alternative courses of action based on available information, knowledge, prior experience, expectation, context, goals, etc. and selecting one preferred option. It is also described as thinking, problem solving and judgment. Memory can be considered to be the storage and retention of information, experiences and knowledge, as well as the ability to
retrieve this information. You should know Ultra short-term memory , the role of sensory stores, Short term memory, long-term memory, Semantic memory, Episodic memory, Iconic memory
Situation awareness The right environment is quickly changing, setting the stage for the creation of active failures. Situation awareness in CRM is tailored to avoid these errors; Line Oriented Flight Training (LOFT) simulations provide flight crews with real-time, simulations to improve future situation awareness. The maintenance environment, thought hectic, changes slowly
relative to flight operations. In terms of situation awareness, engineers must have the ability to extrapolate the consequences of their errors over hours, days or even weeks. To do this, the
situation awareness cues that are taught must be tailored to fit the maintenance environment using MRM-specific simulations. Situation awareness is the synthesis of an accurate and up-to-
date 'mental model' of one's environment and state, and the ability to use this to make predictions of possible future states. An example of situation awareness is an engineer seeing (or perceiving) blue streaks on the fuselage. His comprehension may be that the lavatory fill cap could be missing or the drain line leaking. If his situation awareness is good, he may appreciate that
such a leak could allow blue water to freeze, leading to airframe or engine damage.
You should know about Decision Making, Memory, and Motor Programs. Motor programs may revert to associative phase Skill behavior is associated with motor programs Repetitive tasks, too low & too high temperature, not enough light and noise can reduce alertness
Poor access to components to be worked on can provoke increased discomfort and high probability of omissions Experienced personnel is more prone to errors by not using FIM
Light sensitive cells are cones only on fovea Fitness/health Counseling is symptom directed coping Hyperventilation: breath slowly and deeply Episodic memory can be influenced by expectations as to what should have happened Echoic memory is auditory 2-8 sec
Iconic memory is visual 0.5-1 sec. Most sleep is spent in stage 2 sleep Phase
3/4 sleep is most beneficial for body recovery =Slow wave sleep Ill health can lead to sickness
Claustrophobia = Claustrophobia can be defined as abnormal fear of being in an enclosed space.
Fear of Physical Access and Fear of Heights can cause mental problems to the engineer!

Chapter 9.3 Social Psychology !
Engineers do not work alone, they work in a system with an organizational culture. In this organization are certain structures and rules. The engineer or a group of engineers influence the organization or are influenced by the organization. The engineer or group has responsibilities and also conflicts. Many tasks can be done better by a team, but a team can also lead an individual to do things which the individual would not normally do (group polarization, risky shift, group thinking). Best technicians are involved in more accidents as they work most when really needed
An example of assertive behavior is when a technician refuses to sign off for unsafe work despite pressure Culture issues, Team working, The disadvantage of teamwork is that responsibility can be delegated, Team performance exceeds individual performance. Social loafing reflects the tendency for someone to work less hard Social loafing is a tendency for some individuals to work less hard on a task when they believe others are working on it Flight deck crew team size is small - two or three members; although the wider team is obviously larger (i.e. flight deck crew
+ cabin crew, flight crew + ATC, ground crew, etc.) Maintenance operations are characterized by large teams working on disjointed tasks, spread out over a hangar. In addition, a maintenance task may require multiple teams (hangar, planning department, technical library, management) each with their own responsibilities. Therefore MRM places equal emphasis on inter team teamwork skills.

The Dirty Dozen, which are 12 areas of potential problems in human factors.
1. Lack of communication
Use logbooks, worksheets, etc. to communicate and remove doubt. Discuss work to be done or what has been completed. Never assume anything.
2. Complacency
Train yourself to expect to find a fault. Never sign for anything you didn’t do [or see done].
3. Lack of knowledge
Get training on type. Use up-to-date manuals. Ask a technical representative or someone who knows.
4. Distraction
Always finish the job or unfasten the connection. Mark the uncompleted work. Lockwire where possible or use torque-seal. Double inspect by another or self. When you return to the job,
always go back three steps. Use a detailed check sheet.
5. Lack of teamwork
Discuss what, who and how a job is to be done. Be sure that everyone understands and agrees.
6. Fatigue
Be aware of the symptoms and look for them in yourself and others. Plan to avoid complex tasks at the bottom of your circadian rhythm. Sleep and exercise regularly. Ask others to check your work.
7. Lack of parts
Check suspect areas at the beginning of the inspection and AOG the required parts. Order and stock anticipated parts before they are required. Know all available parts sources and arrange for
pooling or loaning. Maintain a standard and if in doubt ground the aircraft.
8. Pressure
Be sure the pressure isn’t self-induced. Communicate your concerns. Ask for extra help. Just say No.
9. Lack of assertiveness
If its not critical, record it in the journey log book and only sign for what is serviceable. Refuse to compromise your standards.
10. Stress
Be aware of how stress can affect your work. Stop and look rationally at the problem. Determine a rational course of action and follow it. Take time off or at least have a short break. Discuss it with someone. Ask fellow workers to monitor your work. Exercise your body.
11. Lack of awareness
Think of what may occur in the event of an accident. Check to see if your work will conflict with an existing modification or repair. Ask others if they can see any problem with the work done.
12. Norms
Always work as per the instructions or have the instruction changed. Be aware the norms don’t make it right. Motivation can be thought of as a basic human drive that arouses, directs and sustains all human behavior. Generally we say a person is motivated if he is taking action to achieve something. Maslows Hierarchy of Needs Maslow considered that humans are driven by two different sets of motivational forces: those that ensure survival by satisfying basic physical and psychological needs; those that help us to realize our full potential in life known as
self-actualization needs (fulfilling ambitions, etc.) First you must satisfy basic needs like food, housing etc, this goes over safety needs, esteem etc. needs up to self actualization.
Peer pressure is the actual or perceived pressure which an individual may feel, to conform to what he believes that his peers or colleagues expect.
The culture of an organization can be described as the way we do things here.
It is a group or company norm. Safety culture is a set of beliefs, norms, attitudes, roles and social and technical practices concerned with minimizing exposure of employees, managers, customers and members of the general public to conditions considered dangerous or hazardous
Whilst safety culture has been discussed from the organizational perspective, the responsibility of the individual should not be overlooked. Ultimately, safety culture is an amalgamation of the
attitude, beliefs and actions of all the individuals working for the organization and each person should take responsibility for their own contribution towards this culture, ensuring that it is a
positive contribution rather than a negative one. Whereas individualism encourages independence, teams are associated with interdependence and working together in some way
to achieve one or more goals. Managers and supervisors have a key role to play in ensuring that
work is carried out safely. It is no good instilling the engineers and technicians with good safety practice concepts, if these are not supported by their supervisors and managers. A leader in a given situation is a person whose ideas and actions influence the thought and the behavior of others.

A good leader in maintenance engineering is:
Motivating his team Reinforcing good attitudes and behavior Demonstrating by example Maintaining the group Fulfilling a management role Skilled management, supervision and leadership play a significant part in the attainment of safety and high quality human
performance in aircraft maintenance engineering. Maintenance Resource Management MRM is not about addressing the individual human factors of the engineer or his manager; rather, it looks at the larger system of human factors concerns involving engineers, managers and others, working together to promote safety. Flight crews are mostly homogenous by nature, in that they are similar in education level and experience, relative to their maintenance counterparts. Maintenance staff are diverse in their range of experiences and education and this needs to be taken into account in a MRM program.

9.4 Factors Affecting Performance
JAR 66.50 imposes a requirement that certifying staff must not exercise the privileges of their certification authorization if they know or suspect that their physical or mental condition renders
them unfit. See CAAIP Many conditions can impact on the health and fitness of an engineer and there is not space here to offer a complete list. However, such a list would include: Minor physical illness (such as colds, u, etc.); More major physical illness (such as HIV, malaria, etc.)
Mental illness (such as depression, etc.) Minor injury (such as a sprained wrist, etc.) Major injury (such as a broken arm, etc.) Ongoing deterioration in physical condition, possibly associated
with the ageing process (such as hearing loss, visual defects, obesity, heart problems, etc.)
Affects of toxins and other foreign substances (such as carbon monoxide poisoning, alcohol, illicit drugs, etc.).
Positive Measures
Aircraft maintenance engineers can take common sense steps to maintain their fitness and health. These include: Eating regular meals and a well-balanced diet Taking regular exercise (exercise sufficient to double the resting pulse rate for 20 minutes, three times a week is often recommended) Stopping smoking Sensible alcohol intake (for men, this is no more than 3 - 4 units a day or 28 per week, where a unit is equivalent to half a pint of beer or a glass of wine or spirit Stress: Domestic and Work Related: Stress can be defined as any force, that when applied to a system, causes some significant modification of its form, where forces can be physical, psychological or due to social pressures. Stress is usually something experienced due to the presence of some form of stressor, which might be a one-o_ stimulus (such as a challenging problem or a punch on the nose), or an on-going factor (such as an extremely hot hangar or an acrimonious divorce). From these, we get acute stress (typically intense but of short duration) and chronic stress (frequent recurrence or of long duration) respectively. Different stressors affect different people to varying extents. Stressors may be: Physical - such as heat, cold, noise, vibration, presence of something damaging to health (e.g. carbon monoxide)
Psychological - such as emotional upset (e.g. due to bereavements, domestic problems, etc.), worries about real or imagined problems (e.g. due to financial problems, ill health, etc.)
Reactive - such as events occurring in everyday life (e.g. working under time pressure, encountering unexpected situations, etc.) AWN47 points out that: A stress problem can manifest itself by signs of irritability, forgetfulness, sickness absence, mistakes, or alcohol or drug abuse. Management have a duty to identify individuals who may be suffering from stress and to minimize
workplace stresses. Individual cases can be helped by sympathetic and skilful counseling which allows a return to effective work and licensed duties. In brief, the possible signs of stress can include: Physiological symptoms - such as sweating, dryness of the mouth, etc.
Health effects - such as nausea, headaches, sleep problems, diarrhea, ulcers, etc.
Behavioral symptoms - such as restlessness, shaking, nervous laughter, taking longer over tasks, changes to appetite, excessive drinking, etc. Cognitive effects - such as poor concentration, indecision, forgetfulness, etc. Subjective effects - such as anxiety, irritability, depression, moodiness, aggression, etc. Pre-occupation with a source of domestic stress can play on ones mind during the working day, distracting from the working task. Work related Stress: Stress can be felt when carrying out certain tasks that are particularly challenging or difficult. This stress
can be increased by lack of guidance in this situation, or time pressures to complete the task or job (covered later in this chapter). This type of stress can be reduced by careful management,
good training, etc. Stress Management - defense or coping Defense strategies involve alleviation of the symptoms (taking medication, alcohol, etc.) or reducing the anxiety (e.g. denying
to yourself that there is a problem (denial), or blaming someone else). Coping is the process whereby the individual either adjusts to the perceived demands of the situation or changes the situation itself. Good stress management techniques include: Relaxation techniques Careful regulation of sleep and diet A regime of regular physical exercise Counseling - ranging from talking to a supportive friend or colleague to seeking professional advice. There is no magic formula to cure stress and anxiety, merely common sense and practical advice. The Effects of Time Pressure and Deadlines The potential stressors in maintenance is time pressure. This
might be actual pressure where clearly specified deadlines are imposed by an external source (e.g. management or supervisors) and passed on to engineers, or perceived where engineers
feel that there are time pressures when carrying out tasks, even when no definitive deadlines have been set in stone. In addition, time pressure may be self-imposed, in which case engineers set themselves deadlines to complete work (e.g. completing a task before a break or before the end of a shift). Managing Time Pressure and Deadlines Those responsible for setting deadlines and allocating tasks should consider: Prioritizing various pieces of work that need to be done
The actual time available to carry out work (considering breaks, shift handovers, etc.)
The personnel available throughout the whole job (allowing a contingency for illness)
The most appropriate utilization of staff (considering an engineers specialization, and strengths and limitations) Availability of parts and spares. Workload - Overload and Under load: it is important to consider this optimum level of stimulation or arousal. Too much boredom is as bad as heavy work overload and both will lead to failures! Workload management in aircraft maintenance should include: ensuring that staff have the skills needed to do the tasks they
have been asked to do and the proficiency and experience to do the tasks within the timescales they have been asked to work within making sure that staff have the tools and spares they need
to do the tasks allocating tasks to teams or individual engineers that are accomplishable (without cutting corners) in the time available providing human factors training to those responsible
for planning so that the performance and limitations of their staff are taken into account encouraging individual engineers, supervisors and managers to recognize when an overload situation is building up. If an overload situation is developing, methods to help relieve
this include: seeking a simpler method of carrying out the work (that is just as effective and still legitimate) delegating certain activities to others to avoid an individual engineer becoming overloaded securing further time in order to carry out the work safely postponing, delaying tasks deadlines and refusing additional work.

Sleep, Fatigue and Shift Work
Sleep is a natural state of reduced consciousness involving changes in body and brain physiology which is necessary to man to restore and replenish the body and brain. Sleep is characterized by five stages of sleep:
Stage 1: This is a transitional phase between waking and sleeping. The heart rate slows and muscles relax. It is easy to wake someone up.
Stage 2: This is a deeper level of sleep, but it is still fairly easy to wake someone.
Stage 3: Sleep is even deeper and the sleeper is now quite unresponsive to external stimuli and so is difficult to wake. Heart rate, blood pressure and body temperature continue to drop.
Stage 4: This is the deepest stage of sleep and it is very difficult to wake someone up. Rapid Eye Movement or REM Sleep: Even though this stage is characterized by brain activity similar
to a person who is awake, the person is even more difficult to awaken than stage 4. It is therefore also known as paradoxical sleep. Muscles become totally relaxed and the eyes rapidly dart back and forth under the eyelids. It is thought that dreaming occurs during REM sleep. Stages 1 to 4 are collectively known as non-REM (NREM) sleep. Stages 2-4 are categorized as slow-wave sleep and appear to relate to body restoration, whereas REM sleep seems to aid the strengthening and organization of memories. Sleep deprivation experiments suggest that if a person is deprived of stage 1-4 sleep or REM sleep he will show rebound effects. This means that in subsequent sleep, he will make up the deficit in that particular type of sleep. This shows the importance of both types of sleep. Circadian rhythms are physiological and behavioral functions and processes in the body that have a regular cycle of approximately a day (actually about 25 hours in man). An example of disrupting circadian rhythms would be taking a flight that
crosses time zones. This will interfere with the normal synchronization with the light and dark (day night). This throws out the natural link between daylight and the bodies internal clock, causing jet lag, resulting in sleepiness during the day, etc. Eventually however, the circadian rhythm readjusts to the revised environmental cues.
Fatigue can be either physiological or subjective. Physiological fatigue reflects the bodies need for replenishment and restoration. Subjective fatigue is an individuals perception of how sleepy they feel
A good rule of thumb is that one hour of high-quality sleep is good for two hours of activity.
It is always sensible to monitor ones performance, especially when working additional hours. Performance decrements can be gradual, and first signs of chronic fatigue may be moodiness,
headaches or finding that familiar tasks seem more complicated than usual. Symptoms of fatigue may include: diminished perception (vision, hearing, etc.) and a general lack
of awareness diminished motor skills and slow reactions
problems with short-term memory channeled concentration - fixation on a single possibly unimportant issue, to the neglect of others and failing to maintain an overview being easily distracted by unimportant matters poor judgment and decision making leading to increased mistakes abnormal moods - erratic changes in mood, depressed, periodically elated and energetic diminished standards of own work.

Alcohol, Medication and Drug Abuse
Performance will be affected by alcohol, medication or illicit drugs. Under both UK and JAA legislation it is an offence for safety critical personnel to carry out their duties whilst under
the influence of alcohol or drugs. Article 13 (paragraph 8) of the UK ANO, states: The holder of an aircraft maintenance engineers license shall not, when exercising the privileges of such
a license, be under the influence of drink or a drug to such an extent as to impair his capacity to exercise such privileges. 6.2 The current law which does not prescribe a blood/alcohol limit,
is soon to change. There will be new legislation permitting police to test for drink or drugs where there is reasonable cause, and the introduction of a blood/alcohol limit of 20 milligrams of
alcohol per 100 milliliters of blood for anyone performing a safety critical role in UK civil aviation (which includes aircraft maintenance engineers). As a general rule, aircraft maintenance engineers should not work for at least eight hours after drinking even small quantities of alcohol and increase this time if more has been drunk. Medication is usually taken to relieve symptoms of an illness. Even if the drugs taken do not affect the engineers performance, he should still ask himself whether the illness has made him temporarily unfit for work. Analgesics used for pain relief, Antibiotics, Anti-histamines widely used in cold cures, Cough suppressants, Decongestants, Pep pills or Sleeping tablets may reduce the fitness to work in aircraft maintenance.
If the aircraft maintenance engineer has any doubts about the suitability of working whilst taking medication, he must seek appropriate professional advice. Illicit drugs such as ecstasy, cocaine and heroin all affect the central nervous system and impair mental function. Smoking
cannabis can subtly impair performance and lead to make wrong judgments for up to 24 hours.
CAAIP highlights the potential for fatigue in aircraft maintenance engineering: Tiredness and fatigue can adversely affect performance. Excessive hours of duty and shift working,
particularly with multiple shift periods or additional overtime, can lead to problems. Individuals should be fully aware of the dangers of impaired performance due to these factors and of their personal responsibilities.

Shift work:
Advantages may include more days off and avoiding peak traffic times when traveling to work.
The disadvantages of shift working are mainly associated with: working unsociable hours, meaning that time available with friends, family, etc. will be disrupted Working when human performance is known to be poorer (i.e. between 4 am and 6 am.) Problems associated with general de synchronization and disturbance of the bodies various rhythms (principally sleeping patterns). introduces the inherent possibility of increased human errors. Working nights can also lead to problems sleeping during the day, due to the interference of daylight, noise etc...

Continuity of Tasks and Shift Handovers
Many maintenance tasks often span more than one shift, requiring tasks to be passed from one shift to the next. The outgoing personnel are at the end of anything up to a twelve hour shift
and are consequently tired and eager to go home. Therefore, shift handover is potentially an area where human errors can occur. Whilst longer shifts may result in greater fatigue, the disadvantages may be offset by the fact that fewer shift changeovers are required (i.e. only 2 handovers with 2 twelve hour shifts, as opposed to 3 handovers with 3 eight hour shifts).
The primary objective of handovers is to ensure that all necessary information is communicated between the out-going and in-coming personnel. Effective task and shift handover depends
on three basic elements: The outgoing persons ability to understand and communicate the important elements of the job or task being passed over to the incoming person.
The incoming persons ability to understand and assimilate the information being provided by the outgoing person. A formalized process for exchanging information between outgoing and incoming persons and a place and time for such exchanges to take place.
Organizations should have a recognized procedure for task and shift handovers which all staff understand and adhere to. This procedure should be listed in the MOE. Ideally the procedure
should provide for sufficient time to be made available by way of a shift overlap, depending on the complexity of task(s) to be handed over. As a guideline, 20 to 30 minutes could be considered
good human factors practice. It would also be good practice for the outgoing shift supervisor to leave a contact telephone number with the incoming shift, in case they have any queries after a
handover has taken place. Whilst all essential information (especially the detailed status of tasks) should be recorded in written form, it is also important to pass this information verbally in
order to reinforce it. This is known as redundancy, or the belt and braces approach.

9.5 Physical Environment !
It is very important that aircraft maintenance engineers remain aware of the extent of the noise around them. It is likely that some form of hearing protection should be carried with them at
all times and, as a rule of thumb, used when remaining in an area where normal speech cannot be heard clearly at 2 meters. white noise are like the hums produced by air Apart from noxious fumes that have serious health implications and must be avoided, working in the presence of fumes can affect an engineers performance, as he may rush a job in order to escape them. If the fumes are likely to have this effect, the engineer should increase the ventilation locally or use breathing apparatus to dissipate the fumes. Lights: It is also important that illumination is available where the engineer needs it (i.e. both in the hangar and one the line). Any supplemental task lighting must be adequate in terms of its brightness for the task at hand, which is best judged by the engineer. When using task lighting, it should be placed close to the work being done, but should not be in the engineers line of sight as this will result in direct glare. It must also be arranged so that it does not reflect off surfaces near where the engineer is working causing indirect or reflected glare. Glare of either kind will be a distraction from the task and may cause mistakes. Relying on touch when lighting is poor is no substitute for actually being able to see what you are doing. If necessary, tools such as mirrors and bore scopes may be needed to help the engineer see into remote areas.

Climate and Temperature
JAR 145.25(c) (AMC) requires that environmental conditions be adequate for work to be carried out, stating: The working environment for line maintenance should be such that the particular maintenance or inspection task can be carried out without undue distraction. It therefore follows that where the working environment deteriorates to an unacceptable level in respect of temperature, moisture, hail, ice, snow, wind, light, dust/other airborne contamination, the particular maintenance or inspection tasks should be suspended until satisfactory conditions are re-established Environmental conditions can affect physical performance. Motion and Vibration 5.1 Aircraft maintenance engineers often make use of staging and mobile access platforms to reach various parts of an aircraft. As these get higher, they tend to become
less stable. Vibration in aircraft maintenance engineering is usually associated with the use of rotating or percussive tools and ancillary equipment, such as generators. Low frequency noise, such as that associated with aircraft engines, can also cause vibration. Vibration between 0.5 Hz to 20 Hz is most problematic, as the human body absorbs most of the vibratory energy in this
range. The range between 50-150 Hz is most troublesome for the hand and is associated with Vibratory-induced White Finger Syndrome (VWF). Pneumatic tools can produce troublesome
vibrations in this range and frequent use can lead to reduced local blood flow and pain associated with VWF. Vibration can be annoying, possibly disrupting an engineers concentration.
Confined Spaces: claustrophobia may be a problem in aircraft maintenance engineering. Working in any confined space, especially with limited means of entry or exit (e.g. fuel tanks) needs
to be managed carefully. When working in a fuel tank, as guard must be outside of the fuel tank!
Working Environment
workplace layout and the cleanliness and general tidiness of the workplace (e.g. storage facilities for tools, manuals and information, a means of checking that all tools have been retrieved from
The aircraft, etc.) the proper provision and use of safety equipment and signage
(such as non-slip surfaces, safety harnesses, etc.) the storage and use of toxic chemical and fluids (as distinct from fumes) (e.g. avoiding confusion between similar looking canisters
and containers by clear labeling or storage in different locations, etc.). The engineers workplace may affect his ability to work safely and efficiently. JAR 145.25(c) - Facility Requirements states:
The working environment must be appropriate for the task carried out and in particular special requirements observed. Unless otherwise dictated by the particular task environment, the working environment must be such that the effectiveness of personnel is not impaired. The working environment comprises the physical environment, the social environment and the tasks that need to be carried out. Working environment interact, for example: engineers are trained
to perform various tasks successful task execution requires a suitable physical environment an unsuitable or unpleasant physical environment is likely to be de-motivating.

9.6 Tasks
Before commencing a task, an individual engineer, engineering team or planner should ask themselves a number of questions. These may include: Do they know exactly what the task is that has to be done? Are the resources available to do it effectively (safely, accurately and
within the time permitted)? Where resources include: personnel; equipment spares; documentation, information and guidance; facilities such as hangar space, lighting, etc. Do they
have the skills and proficiency necessary to complete the task? information about specific tasks should be detailed on job cards or task sheets. It is generally the shift supervisors job to ensure that the re- sources are available for his staff to carry out their tasks. Although management have a responsibility to ensure that their engineers have suitable training, at the end of the day, it is up to the individual engineer to decide whether he has the necessary skills and has the proficiency and experience to do what he has been asked to do. Physical work As an engineer gets older, the musculoskeletal system stiffens and muscles become weaker. Injuries become more likely and take longer to heal. Staying in shape will minimize the effects of ageing, but they still occur.
Missing a break in an effort to get a job done within a certain time frame can be counterproductive, as fatigue diminishes motor skills, perception, awareness and standards. As a consequence, work may slow and mistakes may occur that need to be rectified. Repetitive tasks
Repetitive tasks in aircraft maintenance engineering typically refer to tasks that are performed several times during a shift, or a number of times during a short time period, e.g. in the course
of a week. An example of this would be the checking life jackets on an aircraft during daily inspections. Complacency is also a danger, whereby an engineer may skip steps or fail to give due attention to steps in a procedure, especially if it is to check something which is rarely found to be wrong, damaged or out of tolerance. Making assumptions along the lines of Oh I’ve done that job dozens of times!
remember that familiarity breeds contempt. Visual inspection Visual inspection can be described as the process of using the eye, alone or in conjunction with various aids to examine and evaluate the condition of systems or components of an aircraft. Good eyesight is of prime importance in visual inspection! The engineer should: ensure that he understands the area, component or system he has been asked to inspect (e.g. as specified on the work card); locate the corresponding area, component or system on the aircraft itself; make sure the environment is conducive to the visual inspection task , such as lighting, access,
etc.); conduct a systematic visual search, moving his eyes carefully in a set pattern so that all parts are inspected; examine thoroughly any potential degradation or defect that is seen and
decide whether it constitutes a problem; record any problem that is found and continue the search a few steps prior to where he left off. Visual inspection requires a considerable amount of concentration. Finally, non-destructive inspection (NDI) includes an element of visual inspection, but usually permits detection of defects below visual thresholds. Various specialist tools are used for this purpose, such as the use of eddy currents and fluorescent penetrate inspection (FPI).

Complex systems
Any complex system can be thought of as having a wide variety of inputs. The system typically performs complex modifications on these inputs or the inputs trigger complex responses. There may be a single output, or many distributed outputs from the
system. With a complex system, it should still be clear to an aircraft maintenance engineer what the systems purpose is. However, its composition and function may be harder to conceptualize it
is opaque to the engineer. To maintain such complex systems, it is likely that the engineer will need to have carried out some form of system-specific training! System-specific training must
achieve the correct balance between detailed system knowledge and analytical troubleshooting skills. When working with complex systems, it is important that the aircraft maintenance engineer makes reference to appropriate guidance material. This typically breaks down the system conceptually or physically, making it easier to understand and work on.

9.7 Communication
An aircraft maintenance engineer might regularly communicate: information; ideas; feelings; attitudes and beliefs As the sender of a message, he will typically expect some kind of response from the person he is communicating with (the recipient), which could range from a simple acknowledgement that his message has been received (and hopefully understood), to a considered and detailed reply. The response constitutes feedback. Communication can be: verbal spoken - e.g. a single word, a phrase or sentence, a grunt; written textual - e.g. printed words And or numbers on paper or on a screen, hand written notes; nonverbal - graphic - e.g. pictures, diagrams, hand drawn sketches, indications on a cockpit instrument; symbolic - e.g. thumbs up,
wave of the hand, nod of the head; body language - e.g. facial expressions, touch such as a pat on the back, posture. Much of flight operations are characterized by synchronous, face-to-face communications, or immediate voice communications (e.g. with ATC) over the radio. The three components of spoken communication are: speaking, listening and feedback To ensure communication ask for feedback in return Communication Within Teams Individual aircraft maintenance engineers need to communicate: before starting a task - to find out what to do; during a task - to discuss work in progress, ask colleagues questions, confirm actions or intentions, or to ensure that others are informed of the maintenance state at any particular time; at the end of a task - to report its completion and highlight any problems. Spoken communication makes up a large proportion of day-to-day communication. Spoken messages provide considerable flexibility and informality to express work-related matters when necessary. The key to such communication is to use words effectively and obtain feedback to make sure your message has been heard and understood.

Communication Between Teams
Communication between teams is critical in aircraft maintenance engineering. It is the means by which one team passes on tasks to another team. This usually occurs at shift handover. The information conveyed will include: tasks that have been completed; tasks in progress, their status, any problems encountered, etc.; tasks to be carried out; general company and technical information. Communication between teams will involve passing on written reports of tasks from one shift supervisor to another. Ideally, this should be backed up by spoken details passed between supervisors and, where appropriate, individual engineers. This means that, wherever necessary, outgoing engineers personally brief their incoming colleagues. The written reports (maintenance cards, procedures, work orders, logs, etc.) and warning flags placards provide a record of work completed and work yet to be completed - in other words, they provide traceability
(see Section 2 below). Furthermore, information communicated at shift handover ensures good continuity. It is important that handovers are not rushed, so as to minimize omissions.
The two main problems are lack of communication and poor communication. The difficulty of written communication is limited feedback and you cannot easily ask questions
The 3 C's in written communication are: Correct writing, Complete writing, Clear writing
Parts of communication are 55% body language, 38% tone of voice and only 7% verbal
Basic rules of thumb to help aircraft maintenance engineers minimize poor communication are: think about what you want to say before speaking or writing; speak or write clearly; listen or
read carefully; seek clarification wherever necessary. Work Logging and Recording: This is one of the most critical aspects of communication within aviation maintenance, since in-adequate logging or recording of work has been cited as a contributor to several incidents.

9.8 Human Error
Errors tend to be active in that their consequences follow on immediately after the error Active failures are direct The consequences of an engineers error are often not immediately apparent, and this has implications for training for error avoidance. Error Models and Theories To appreciate the types of error that it is possible to make, researchers have looked at human error
in a number of ways and proposed various models and theories. These attempt to capture the nature of the error and its characteristics. Examples: design- versus operator-induced errors; variable versus constant errors; reversible versus irreversible errors; slips, lapses and mistakes; skill-, rule- and knowledge-based behaviors and associated errors; the Swiss Cheese Model.
Slips can be thought of as actions not carried out as intended or planned, e.g. transposing digits when copying out numbers, or miss-ordering steps in a procedure. Lapses are missed actions and omissions, i.e. when somebody has failed to do something due to lapses of memory and/or attention or because they have forgotten something, e.g. forgetting to replace an engine cowling.
Mistakes are a specific type of error brought about by a faulty plan/intention, i.e. somebody did something believing it to be correct when it was, in fact, wrong, e.g. an error of judgment
such as mis-selection of bolts when fitting an aircraft windscreen. Latent failures are dormant and may lead to problems A mistake is not intended An error is not intended e.g. pulling the wrong circuit breaker Violations sometimes appear to be human errors, but they differ
from slips, lapses and mistakes because they are deliberate illegal actions, such as cutting corners, There are four types of violations: Routine violations; Situational violations; Optimizing violations; Exceptional violations. Time pressure and high workload increase the likelihood of all
types of violations occurring. People weigh up the perceived risks against the perceived benefits, unfortunately the actual risks can be much higher. Skill-based behaviors are those that rely on stored routines or motor programs that have been learned with practice and may be executed without conscious thought. Rule-based behaviors are those for which a routine or procedure has been learned. The components of a rule-based behavior may comprise a set of discrete skills.
Knowledge-based behaviors are those for which no procedure has been established. These require the [aircraft maintenance engineer] to evaluate information, and then use his knowledge
and experience to formulate a plan for dealing with the situation. Any maintenance task performed on an aircraft is an opportunity for human error to be introduced. Errors in aircraft maintenance engineering tend to take two specific forms: ) an error that results in a specific aircraft problem that was not there before the maintenance task was initiated; ii) an error that results in an unwanted or unsafe condition remaining undetected while performing a maintenance task designed to detect aircraft problems, i.e. something is missed. Where procedures allow some leeway, aircraft maintenance engineers often develop their own strategies or preferred way of carrying out a task - Rule of thumb In addition, engineers may pick up some bad rules, leading to bad habits during their working life

Errors Associated With Visual Inspection :
A Type 1 error occurs when a good item is incorrectly identified as faulty;
a Type 2 error occurs when a faulty item is missed.
Reasons Study of Aviation Maintenance Engineering main causes are: Omissions (56%) Incorrect installation (30%) Wrong parts (8%) Other (6%)

UK Civil Aviation Authority Mandatory Occurrence Reporting Scheme (MORS).
These data are used to disclose trends and, where necessary, implement action to reduce the likelihood or criticality of further errors. In the UK, the Confidential Human Factors Incident Reporting Program (CHIRP) scheme provides an alternative reporting mechanism for individuals who want to report safety concerns and incidents confidentially. It is vital that aircraft maintenance engineers learn from their own errors and from the errors made by others in the industry.
These powerful and persuasive lessons are the positive aspects of human error.
Error management seeks to: prevent errors from occurring; eliminate or mitigate the bad effects of errors To prevent errors from occurring, it is necessary to predict where they are most likely to occur and then to put in place preventative measures. Incident reporting schemes (such as MORS) do this for the industry as a whole. Within a maintenance organization, data on errors, incidents and accidents should be captured with a Safety Management System (SMS), which should provide mechanisms for identifying potential weak spots and error- prone activities or situations. Output from this should guide local training, company procedures, the introduction of new defenses, or the modification of existing defenses. Boeing brought out a similar system called MEDA, it is sometimes asked in Essay questions! One of the things likely to be most effective in preventing error is to make sure that engineers follow procedures. This can be
effected by ensuring that the procedures are correct and usable, that the means of presentation of the information is user friendly and appropriate to the task and context, that engineers are encouraged to follow procedures and not to cut corners.

9.9 Hazards in the Workplace
Hazards in the workplace tend to be a health and safety issue, relating to the protection of individuals at work. Recognizing and avoiding hazards There are many potential hazards in aircraft maintenance Physical hazards may include: very bright lights (e.g. from welding); very loud sounds (sudden or continuous); confined or enclosed areas; working at significant heights; noxious substances (liquids, fumes, etc.); excessive temperature (i.e. too cold or too hot); moving equipment, moving vehicles and vibration. The health and safety policy might include statements applicable to the organization such as the need to: Carry out assessments of work including inspections to determine Health and Safety risks; Provide safe working practices and procedures for plant, machinery, work equipment, materials and substances; Inform employees and other persons including temporary workers of any risk; Provide suitable training and or instruction to meet any Health and Safety risks; Develop and introduce practices
and procedures to reduce risks to Health and Safety including the provision of special protective devices and personal protective equipment; Provide for the welfare of employees; Discuss
with and consult employee representatives on Health and Safety matters. In brief, a maintenance organization has a duty under health and safety legislation to: identify hazards in the workplace; remove them where possible; mitigate the risks to employees. Warning sign must attract an engineers attention! The health and safety policy might include statements applicable to engineers such as the need to: Take reasonable care of the health and safety of themselves and others who may be affected by their acts or omissions at work; Co-operate with the maintenance organization to ensure that statutory requirements concerning health and safety at work are met; Work in accordance with any safety instruction and or training received; Inform their supervisor or management of work situations that represent an immediate or potential danger to health and safety at work and any shortcomings in protection arrangements; Not interfere intentionally or recklessly with, nor misuse, anything provided in the interests of health and safety.
It is necessary to establish and organizational safety culture! Poor housekeeping is causing most accidents! It is imperative that engineers working remotely from the engineering base (e.g. on the line) familiarize themselves with new information (on notice boards, in maintenance manuals, etc.) on a regular basis.

Dealing with emergencies
Should health and safety problems occur, all personnel should know as far as reasonably practical how to deal with emergency situations. Emergencies may include: An injury to oneself or to a colleague; A situation that is inherently dangerous, which has the potential to cause injury (such as the escape of a noxious substance, or a fire). Appropriate guidance and training and drills should be provided by the maintenance organization. The basic actions in an emergency are to: Stay calm and assess the situation Observe what has happened; Look for dangers to oneself and others; Never put oneself at risk. Make the area safe Protect any casualties from further danger; Remove the danger if it is safe to do so (i.e. switching off an electrical current if an electrocution has occurred); Be aware of ones own limitations (e.g. do not fight a fire unless
it is practical to do so). Assess all casualties to the best of ones abilities (especially if one
is a qualified first aider) Call for help Summon help from those nearby if it is safe for them to become involved;
Call for local emergency equipment (e.g. fire extinguisher);
Call for emergency services (ambulance or _re brigade, etc.).
Provide assistance as far as one feels competent to.

MODULE 9 HUMAN FACTORS SYLLABUS

THE SYLLABUS FOR HUMAN FACTORS


9.1 General
The need to take human factors into account;
Incidents attributable to human factors/human error;
‘Murphy's’ law.

9.2 Human Performance and Limitations
Vision;
Hearing;
Information processing;
Attention and perception;
Memory;
Claustrophobia and physical access.

9.3 Social Psychology
Responsibility: individual and group;
Motivation and de-motivation;
Peer pressure;
‘Culture’ issues;
Team working;
Management, supervision and leadership.

9.4 Factors Affecting Performance
Fitness/health;
Stress: domestic and work related;
Time pressure and deadlines;
Workload: overload and underload;
Sleep and fatigue, shiftwork;
Alcohol, medication, drug abuse.

9.5 Physical Environment
Noise and fumes;
Illumination;
Climate and temperature;
Motion and vibration;
Working environment.

9.6 Tasks
Physical work;
Repetitive tasks;
Visual inspection;
Complex systems.

9.7 Communication
Within and between teams;
Work logging and recording;
Keeping up to date, currency;
Dissemination of information.

9.8 Human Error
Error models and theories;
Types of error in maintenance tasks;
Implications of errors (i.e accidents)
Avoiding and managing errors.

9.9 Hazards in the Workplace
Recognising and avoiding hazards;
Dealing with emergencies.

EASA PART 66 B2 AVIONICS

THE  INFORMATION ON THIS BLOG WILL NOT GUARANTEE YOU A PASS AT THE EXAMS, BUT IT WILL HELP A GREAT DEAL, I AM OFFERING IT FREE AS THE EXAMS COST ALOT AND IF YOU ARE NOT NEAR AN EXAM LOCATION, THEN IT AIR TICKETS AND ACCOMODATION,

IT WILL TAKE A GREAT DEAL OF STUDYING, CROSS REFERENCE MIGHT BE REQUIRED TO SEE IF THE INFORMATION IS STILL UP TO DATE WITH CAA UK AND EASA.

SUGGESTED SITES FOR STUDYING WITH TUTORS ARE www.licencebypost.com AND www.jartraining.de THESE ARE THE ONLY 2 THAT I AM AWARE OF.

I AM CURRENTLY BUSY WITH MY B2 AVIONICS LICENSE AND WILL POST THE MODULE INFORMATION AS I HAVE DONE THEM AND WILL INFORM YOU IF THE INFORMATION ON THIS BLOG WILL BE SUFFICIENT TO PASS THE EXAMS AS IT IS ALL THAT I AM USING.